Messages

1

Plumbing and Galley Systems / Diaphragm

« on: May 09, 2025, 09:42:44 PM »

On my 323 the freshwater pump diphragm is leaking.  Did it come with a certain brand and size, can you replace the diphragm?

2

Sails and Canvas / Re: loose or fixed foot

« on: June 24, 2024, 08:41:34 PM »

Here it is from Precision Sails.  Changed the tack angle from 88.6 to 85.4.  It will rase the boom 7".  At 88.6 it was 1" off the dodger.  I know it will stretch over the years, the one I have now have to put dodger down to be able to sail.

3

Engine and Drive Train / Re: new motor

« on: June 24, 2024, 11:26:18 AM »

Still want to know the answer to this question but don't need a new motor...

4

Engine and Drive Train / Re: Oil pressure

« on: June 24, 2024, 11:24:45 AM »

Just to let you know, I found the oil leak.  Eight years ago I put on an remote oil filter on to better access the filter.  The oil lines to the remote was against the bulkhead and finally rubbed a hole in it.  Replaced hoses and all is good.  No new motor needed.

5

Engine and Drive Train / new motor

« on: June 20, 2024, 11:30:58 AM »

I am looking at a Bata 25 to put in the 323.  I have found a place in Indonesia.  Its name is   (Marine Power Engine).  He is selling the new motor for $3,200.00 shipping $435.00.  That is close to 7,000.00 less than the places in america.  Is this a scam or has any one purchased from this company? 

6

For Sale and Wanted / Re: Lifelines

« on: June 12, 2024, 09:29:49 PM »

A big thank's the fellow that needed them got in touch with me...

7

For Sale and Wanted / Lifelines

« on: June 06, 2024, 08:52:16 AM »

I have replaced my lifelines with a gate.  I thought I saw somewhere on this site that someone needed some lifelines for a 323.  If you know who it was they can have the ones I took off cheep...  If you know who it was, let me know.

8

Engine and Drive Train / Oil pressure

« on: June 06, 2024, 08:43:04 AM »

Looked down no oil pressure (MD11C).  Added oil, few minutes no oil presure.  oil is in bilge.  Can't see it coming from anywhere.  Any ideas...

9

Sails and Canvas / loose or fixed foot

« on: March 18, 2024, 05:39:23 PM »

Am ordering a new main sail and everything I have read was loose footed is the way to go.  Am I just old school or should I move up with the times. 

10

For Sale and Wanted / Re: Prop

« on: June 16, 2023, 04:23:59 PM »

I saw somewhere else in this forum that I need a   (LH 17X12 style E) does that sound right?

11

For Sale and Wanted / Prop

« on: June 16, 2023, 10:17:10 AM »

Looking for a 3 blade prop for my Pearson 323.  It has an 1 1/8" shaft and Volvo MD11 diesel I am not sure of the size or pitch it should be.  I believe it should be left hand.  Used good shape or new.
Thanks, Dick                              I am tired of not being able to back up...

12

Engine and Drive Train / Re: throttle cable end

« on: October 20, 2022, 07:18:13 AM »

The ball end is part of the throttle shaft on the motor it does not unscrew.  I will keep looking.  The threaded end to the plastic piece  is 5mm or 10-32, not sure of ball size will have to measure this weekend.  I had better hurry leaving for our annual race in Southport.NC Thursday the 28th.  If I have to use zip ties to hold it on I will...

13

Engine and Drive Train / throttle cable end

« on: October 18, 2022, 12:58:08 PM »

I have an Volvo MD11c.  The throttle control cable end, that connects to the ball on throttle shaft is shot.  It is also plastic.  I am looking for replacement or part number.  Any help would be appreciated.

14

General Discussion / Re: Builder's Plate

« on: August 29, 2022, 09:37:28 AM »

Valor, Used the same mounting screws.  And yes it uses the same mounting holes.

15

General Discussion / Re: Builder's Plate

« on: June 20, 2022, 07:00:48 PM »

https://www.blazinlazin.com/  Ed that is where I purchased it from and it was $100.00.  It took about two week's .  I found it on this site under general on the second page.  Hope your doing well.